Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Wellborn Fence Installation: The Dallas Owner’s Guide
Wellborn fence installation in Dallas typically runs $3,500 to $9,000 for a complete vinyl fence, with most standard residential jobs landing between $4,500 and $6,500. We install Wellborn-compatible vinyl fencing and matching gates, and we keep common replacement components on the truck so a failed section or post usually gets swapped in a single visit. Most owners discover a problem the hard way: a post that’s leaning after a spring storm, a gate that drags across the concrete, or a bottom rail that’s cracked right where the weed trimmer keeps hitting it.
What surprises people is that Wellborn-quality vinyl fencing almost never fails on its own. The fence material itself will outlast your mortgage. What fails is what touches it: the concrete footing under the post, the hinges on a gate, or the fasteners holding a panel to post that’s started to pull loose. That’s the part worth understanding before you spend a dime.
Key takeaways:
- Wellborn vinyl fencing installed in Dallas: $3,500-$9,000 depending on linear feet, gate count, and site conditions.
- Most failures are post footing, gate hardware, or impact damage. The vinyl itself rarely breaks down.
- We match replacement sections to your existing profile and color. You don’t have to replace the whole fence line.
- Every job gets a written price before we start and a 365-Day Done Right Promise in writing.
Which Wellborn Models This Applies To
Wellborn offers vinyl fence in three main profiles you’ll see around Dallas neighborhoods: privacy (tongue-and-groove, no gaps), semi-privacy (narrow spacing between pickets), and picket (decorative, usually 3-4 feet tall for front yards). The compatibility gotcha is that the bottom rail and post dimensions are not universal across these profiles. A privacy panel’s bottom rail sits about 1.5 inches thick with a reinforced aluminum insert on some lines; a picket panel’s rail is thinner and sometimes hollow. If you buy a replacement panel that “looks close,” it won’t seat into your existing posts correctly, and it’ll rattle or bind at the first temperature swing.
Here’s what we do before recommending any replacement section. We check the markings on the inside of the top or bottom rail for a manufacturer stamp, measure the picket width and wall thickness, and verify the post size (usually 4×4 or 5×5 for Wellborn). Then we match the texture: Wellborn uses a wood-grain finish on most privacy lines, and a smooth finish on some picket styles. On OEM versus aftermarket: Wellborn’s own components carry the longest color-retention record, but there are quality aftermarket sections made to the same dimensions at about 70-80% of the price. We’ll quote both and tell you honestly which makes sense for a 60-foot run versus two broken pickets. Since 2004, operating under The Kingswell Way, we’ve learned that putting the real choice in front of the homeowner beats making it for them.
Styles & brands we work with
Signs Your Wellborn Fence Installation Is Failing
If you walk your fence line after the next hard rain, most problems announce themselves pretty clearly. Here’s what we see most often on service calls around Oak Cliff, White Rock Lake, and the northern suburbs:
- Post lean at the corner or gate posts. This almost always means the concrete footing was poured too shallow or started cracking out. In Dallas clay soil, a 2-foot post hole for a 6-foot privacy panel is asking for trouble. We dig to 30-36 inches and set posts below the frost line even though North Texas rarely freezes deep. The clay expands and contracts enough on its own.
- Gate drag or a latch that won’t catch. The hinge screws pull loose from the post, or the gate sags because the diagonal brace was never installed or has cracked at the fastener. You’ll see a wear mark on the concrete where the gate bottom scrapes.
- Bottom rail cracking along its length. This is usually impact from a string trimmer or a mower wheel, compounded by sun exposure that makes the vinyl more brittle at ground level. Once the bottom rail splits, the pickets start to wobble and the panel loses its rigidity.
- Pickets popping out of the top rail. The top rail expands in direct Texas sun, and the locking tabs wear down. You’ll see a gap form at the end of the panel, especially in runs longer than 8 feet with no mid-rail support.
- Chalky, streaky appearance on sun-facing sides. Wellborn’s vinyl has good UV protection, but after 8-10 years of southern exposure, the surface starts to oxidize. It’s cosmetic at first. If you ignore it, the surface becomes rougher and holds dirt, which accelerates the wear.
Replacement Cost & What’s Included
For a full Wellborn-compatible vinyl fence installation in Dallas, you’re looking at $3,500 to $9,000. A typical 100-linear-foot privacy fence with one gate runs about $4,500 to $5,800. Here’s what moves the number:
- Linear footage: The biggest driver. Every 8-foot section adds roughly $280-$420 in material and labor.
- Gate count and type: A single walk gate might add $300-$600. A double-drive gate with steel frame adds $1,200-$2,000 because of the hardware and the reinforced posts.
- Post setting conditions: Clay is straightforward. But if we’re digging through caliche, limestone shelf, or tree roots, each post hole takes longer.
- Tear-out and disposal of the old fence: Usually $5-$9 per linear foot, included if we’re replacing an existing fence.
- Partial repair vs. full replacement: A single replacement section with two posts might run $350-$700. We’ll tell you plainly if a full panel swap makes more sense than patching.
Every estimate is written, line-itemed, and fixed before we pick up a tool. That’s Trevor Nash’s rule around here: give you a number before I pick up a tool, that’s the only way I know how to start. The 365-Day Done Right Promise covers the work in writing. If a post shifts or a gate binds inside that year, we come back and fix it at no charge. No re-inspection fee. No service call charge. Plain and simple.
See the difference
Before
After
Before
After
Before
AfterDIY or Call Us?
You can absolutely reset a leaning post yourself if you’re comfortable with a post-hole digger and a bag of quick-set concrete. That’s honest. The safe checks: walk the line, mark which posts move when you push them, and note which gate hinges have pulled screws. What we don’t recommend is attempting a full panel replacement on your own if the posts are set in concrete and you want the new panel to seat square. Vinyl doesn’t flex to forgive a half-inch error. If the post spacing is off, the panel won’t lock in, and you’ll have a fence that looks fine from the street but wobbles in the wind. The bigger risk is digging blind. In Dallas, you’re supposed to call 811 before any excavation, and a surprising number of yards have irrigation lines or low-voltage wiring running right along the fence line. A confident weekend with a post-hole digger can turn into a $400 sprinkler repair faster than most people expect.
Independent note: Penhallow Remodeling Dallas is an independent contractor serving Dallas homeowners. We’re not affiliated with Wellborn, but we install Wellborn-compatible fencing and have years of hands-on time with their profiles and hardware.
FAQs
Wellborn vinyl fencing realistically lasts 20-30 years in the Dallas climate, with color retention strongest on the north and east sides of the fence. South-facing and west-facing sections take the brunt of the Texas sun and may start to chalk after 8-10 years, but the structural integrity still holds well past that point. Call (940) 204-5368 if you want us to assess whether your fence is at replacement stage or just needs a few sections swapped.
Yes, in most cases a cracked bottom rail can be repaired by cutting out the damaged section and splicing in a matching rail segment with an internal stiffener, which runs about $120-$250 per repair in Dallas. If the crack runs more than half the rail length or multiple pickets have pulled loose, replacing the full section makes more sense. Call (940) 204-5368 and we’ll tell you which one your fence actually needs.
A single section replacement with post resetting takes about 3-4 hours from start to clean job site, and most jobs are done in one visit. Full fence installations of 100 linear feet or more typically take 2-3 days depending on site access and tear-out conditions.
We stock common Wellborn-compatible replacement parts on our service trucks: bottom rails, pickets, gate hinges, latches, and post caps in standard colors like white and tan. For less common colors or specialty profiles, we order from our local supplier and typically have parts in hand within 3-5 business days. Call (940) 204-5368 and we’ll check what’s on the truck before you even schedule.
Get Your Written Estimate
If your Wellborn fence is leaning, cracked, or dragging, call (940) 204-5368. We’ll schedule a site visit, measure what’s there, and hand you a written price before any work starts. You’ll know the number, the arrival window, and the guarantee, all in writing. That’s how we’ve done it since 2004, and that’s how we’ll do it on your fence.
Written by Trevor Nash, Owner, Penhallow Remodeling Dallas at Penhallow Remodeling Dallas, serving Dallas and nearby areas.
