Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
ActiveYards Fence Installation: The Dallas Owner’s Guide
ActiveYards fence installation in Dallas typically runs $3,500 – $9,000, depending on the series, lineal footage, gate count, and whether we’re pulling old posts or setting new ones. We stock ActiveYards-compatible components on the truck, and most panel-and-post installs go in on a single day. Homeowners usually find us after a windstorm has taken out a section, or after years of North Texas clay heave has popped posts out of line and the gate no longer latches. The most common call we get: “The fence was fine last week, now it’s leaning and the gate drags.”
If you have ActiveYards product already on the property, you already know it’s a measured, engineered aluminum fence line, not a lumberyard afterthought. The good news is that ActiveYards’ component system means we can usually match existing sections without ripping out the whole run. The less-obvious news, and the thing that costs owners the most when it’s missed, is that rail brackets and gate hinges on this product line are series-specific. Mix a Grand Estate bracket on a Traditions II rail and you’ll hear it rattle in a Dallas wind from two houses over.
Which ActiveYards Models This Applies To
We work with the full residential ActiveYards lineup: Traditions, Traditions II, Grand Estate, Hampton, and the Prescott series. Each series has its own rail profile, post dimensions, and bracket geometry, so the first question on any repair or replacement call is simple: do you have the original paperwork, or do we need to measure? If the paperwork is long gone, we identify the series by measuring the rail cross-section and checking the screw pattern on the gate hinge plate. It takes about ten minutes, and Trevor Nash would rather spend those ten minutes than order the wrong rail and put a three-week hole in your fence line.
On the OEM-versus-aftermarket question for ActiveYards specifically: we prefer OEM for the visible structural pieces, rails, posts, and gate frames, because the powder-coat color is matched at the factory, not estimated in the field. For bracket hardware and post caps, there are quality aftermarket equivalents that hold up fine in Texas weather. One specific gotcha worth knowing: ActiveYards posts are engineered as a two-piece system with an internal stiffener, so a “universal” post from a big-box store will not carry the wind load the original design assumes. Dallas gets sustained 30 mph spring winds often enough that we won’t install a substitute post on a corner or gate post, ever.
Styles & brands we work with
Signs Your ActiveYards Fence Installation Is Failing
- Leaning posts at the corners or gate openings. In Dallas’s shrink-swell clay, the post was either never set deep enough or the concrete footing is undersized for the wind load. The fix is a new deeper footing, not just straightening the post.
- Gate drags or no longer latches. Frame sag on an ActiveYards gate usually means the hinge screws have wallowed out or the frame rail corner brackets have loosened. Left alone, the gate frame twists and the latch side drops another half inch each season.
- Rattle coming from the pickets. Pickets on ActiveYards panels are press-locked into the rails and held with a punched tab. When the tab rusts or a rail gets stressed, the pickets start buzzing. Every gust tells you where the loose section is.
- White chalky powder or dark spotting on the finish. North Texas hard water and UV are both hard on powder coat. Once the chalk starts, the coating’s not coming back, but the section can be replaced without redoing the run.
- Post cap missing and water pooling inside the post. A missing cap lets irrigation overspray and rain sit inside the post. In Dallas’s freeze-and-swell winters, that trapped water does more damage than the weather outside.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Most ActiveYards fence installs we do in Dallas land between $3,500 and $9,000. A partial repair, say, two sections and a gate rehang, runs lower. A full perimeter with two gates, corner posts, and removal of an old wood fence runs toward the top. What drives the range more than anything is lineal footage and gate count. Every gate adds at least three posts, hardware, and a frame that has to be squared and adjusted, and gates are where most of the failure we see originates.
We quote ActiveYards work the same way we quote every job at Penhallow Remodeling Dallas: a written price before we start, not a verbal ballpark you have to trust. The number you get is the number on the invoice. The warrantable parts come from ActiveYards-compatible supply, and our install labor carries the 365-Day Done Right Promise. If a post shifts or a gate drops inside that year, we come back at no charge. That’s in writing, the same as our repair guarantee on every job.
DIY or Call Us?
Aluminum fence work is not like framing or concrete, where the worst-case scenario is cosmetic. The safety issue here is a high-tension gate under spring load and a panel that, once unbolted, weighs enough to pin a hand or foot if it drops. We never recommend pulling an ActiveYards panel without a second person and sawhorses set. A homeowner can safely check post plumb with a level, inspect hinge screws for wallow, and spray the latch with dry lube. Replacing a full post or re-squaring a sagging gate frame is where we’d suggest stopping.
If the section is down and the gate is off its hinges, that’s our job. Call us at (940) 204-5368 and we’ll bring the right series parts the first trip. Written price before any work starts, and a real arrival window, not “sometime Tuesday.”
FAQs
An ActiveYards aluminum fence properly installed in Dallas should last 20 – 30 years on the structural components, with the powder coat showing weather wear in 10 – 15 years depending on sun exposure and sprinkler overspray. The hardware, hinges, and brackets, typically fail first and usually need attention in years 8 – 12. If you’re seeing chalky powder coat on a ten-year-old fence, the structure’s still sound and replacing one section is cheaper than a full redo. Call (940) 204-5368 and we’ll give you a straight number.
Yes, in most cases individual sections, posts, and gate frames can be repaired or swapped without replacing the whole run. The exception is when the original install set multiple posts too shallow in Dallas clay, at which point we usually recommend fixing the footings on every affected post rather than spot-patching forever. We’ll tell you if a repair will buy you five years or if you’re paying twice for the same failure. Estimates are free.
A partial repair, two or three sections and a gate rehang, is usually done in one day. A full perimeter install with multiple gates and old fence removal in Dallas typically takes two to four working days, depending on layout and how much concrete demo is involved with old posts. You’ll get the schedule in writing before we start. Call (940) 204-5368 for a written quote.
We keep common ActiveYards-compatible rails, brackets, post caps, and gate hardware on the truck, and the busiest series (Traditions, Traditions II, Grand Estate) we can usually match within a day or two. More specific color matches or full gate frames may take a week from the supplier. We’ll tell you before you commit. Call (940) 204-5368 and we’ll check availability while you’re on the phone.
Written by Trevor Nash, Owner, Penhallow Remodeling Dallas at Penhallow Remodeling Dallas, serving Dallas and nearby areas.
