Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Belgard Bathroom Remodeling: The Dallas Owner’s Guide
Belgard bathroom remodeling in Dallas typically runs $9,000 to $28,000 installed, depending on whether you’re replacing a failing Belgard paver shower floor, rebuilding a Belgard paver accent wall, or doing a full Belgard-paver wet room. We carry Belgard-compatible pavers, coping pieces, and matching trim on our trucks for common Belgard lines, which means most repairs get priced and scheduled the same day we inspect. The owner usually finds out something failed the hard way: a paver shifts underfoot in the shower and water starts pooling where it used to drain, or a Belair paver edge starts spalling (flaking) because the original installer skipped a sealant coat designed for a wet environment.
Which Belgard Models This Applies To
The Belgard name shows up in Dallas bathrooms most often through their Cambridge, Belair, and Mega-Arbel paver lines, though some homeowners also spec Belgard’s thinner coping and tread pieces for shower curbs and bench caps. If you’re trying to identify what you have, flip a loose paver (carefully) or check the original invoice; Belgard marks most products with a lot code on the underside. The catch with Belgard paver bathrooms specifically: outdoor-rated pavers aren’t all rated for constant standing water. We see failures in Dallas when a contractor installed a standard outdoor paver in a shower pan without the proper slope or drainage bed. For a wet-area application, you need the right base (mortar-set on a pre-sloped pan, not sand-set), the correct edge restraint, and a penetrating sealant rated for interior wet use. We can match existing Belgard product if it’s still in production; when a line is discontinued, we’ll pull matching samples from our supplier network so the replacement doesn’t look like a patch job.
Styles & brands we work with
Signs Your Belgard Bathroom Remodeling Is Failing
- Water pools instead of draining. This usually means the substrate beneath the pavers has settled or the original slope was never pitched correctly. Pavers don’t fail first; bases do.
- Pavers shift or rock when you step on them. A loose paver in a shower tells you the setting bed is breaking down. Ignoring it lets water reach the waterproofing layer and eventually the subfloor.
- Edges spall or flake. Pavers absorbing water and then drying repeatedly in a Texas climate cycle can delaminate at the surface. Improper sealer or no sealer is the typical culprit.
- Efflorescence (white chalky residue) keeps coming back. This is mineral salt wicking up through the paver. The real issue is moisture moving through the piece, not the stain on top of it.
- Grout or joint sand washes out after every shower. In a wet room, joint material shouldn’t erode. When it does, water is getting behind the pavers and working on your waterproofing layer.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
A full Belgard paver bathroom remodel in Dallas lands between $9,000 and $28,000. The spread is driven by shower size, whether we’re pulling and resetting the waterproofing membrane, if the bathroom needs structural floor work, and which Belgard line you’re matching. A shower floor-only rebuild with new pavers and proper slope usually starts around $3,500 for the paver portion when we’re already working inside a bathroom scope. Every Penhallow job comes with a written price before any work starts, a written 365-Day Done Right Promise, and a clean job site at the end of each day. If the repair fails inside that year, we come back and fix it at no charge. That’s the agreement, in writing, on every project.
DIY or Call Us?
You can safely check a few things yourself: look for missing or cracked grout, note where water pools, and check whether pavers move underfoot. What we don’t recommend is pulling pavers yourself. Once you lift a piece, you’ve broken the seal between the pavers, the setting bed, and the waterproofing below. Most Dallas homeowners don’t have a wet-rated sealant on hand, and rebuilding slope correctly is a technical job that requires a level, a proper mortar bed, and an understanding of drainage plane. If you suspect waterproofing damage, water is already doing work below the surface, and that’s a professional repair. Give us a call at (940) 204-5368 and we’ll inspect it, quote it in writing, and tell you exactly what we’re going to do before we pick up a tool.
FAQs
A properly installed Belgard paver bathroom with the right sealer and drainage typically lasts 20 to 30 years before the setting bed or waterproofing needs attention; sealed pavers in wet areas usually need re-sealing every 3 to 5 years in Dallas’s heat and humidity cycle. Call (940) 204-5368 and we’ll tell you if yours is salvageable.
We can often repair isolated areas if the waterproofing membrane is intact, but if the base has settled or the slope failed, a full rebuild of the affected section is the only lasting fix. We’ll inspect before quoting so you’re never paying for work you don’t need.
A shower floor rebuild usually takes 3 to 5 working days, including demo, re-sloping, setting, grouting, and sealant cure time. We give you a defined window before work starts and keep it.
We stock common Belgard Cambridge, Belair, and Mega-Arbel pieces and can source matching product or discontinued lines through our supplier network, usually within a week. You never pay a parts markup that isn’t on your written quote.
Written by Trevor Nash, Owner, Penhallow Remodeling Dallas at Penhallow Remodeling Dallas, serving Dallas and nearby areas.
