Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
PGT Fence Installation: The Dallas Owner’s Guide
If you’re looking for PGT fence installation in Dallas, you’re likely holding a warranty card for a fence that’s sagging, leaning, or pulling loose at the posts after a few hard Texas seasons. A complete PGT-compatible fence installation in the Dallas area typically runs $3,500 to $9,000 depending on linear footage, post depth, and whether we’re pulling an old fence or starting fresh. Most owners discover the problem the same way: a gate that drags, a post that won’t stay plumb, or rails that pulled their fasteners clean out during a spring storm. We stock the common PGT-compatible hardware on the truck and can usually get a Dallas crew out within a few days once we’ve confirmed the right profile.
One thing to clear up before we go further: Penhallow Remodeling Dallas is an independent contractor, not affiliated with PGT. We install and repair fences built with PGT profiles and match their hardware where it’s still available. If a PGT-specific part has been discontinued, we’ll tell you that plainly and show you what we use instead.
Which PGT Models This Applies To
PGT’s fencing footprint in Dallas is mostly aluminum and vinyl lines, and the compatibility question usually comes down to three things: post size, rail profile, and picket spacing. If you still have the original paperwork, look for a model code like Arlington, Kendall, or Sierra, but plenty of Dallas homeowners lost that paper years ago. The more reliable way is to measure the post: most PGT aluminum lines use 2-inch square posts with a notched rail, while the vinyl lines step up to 2.5-inch posts with a routed pocket. That difference matters because a 2-inch PGT rail won’t seat correctly in a 2.5-inch aftermarket post, and forcing it is how you get a fence that rattles in the wind.
The OEM versus aftermarket decision for PGT is simpler than for some brands. PGT’s aluminum extrusions are still available for many lines, and the coating holds up better than the generic powder-coat we’ve seen peel on cheaper replacements after three Dallas summers. If a PGT part is on backorder or discontinued, we’ll only offer an aftermarket equivalent that matches the wall thickness and coating spec, not just the dimensions. We’d rather tell you to wait two weeks than hang a rail that’s going to oxidize at the screw holes before the year’s out.
Styles & brands we work with
Signs Your PGT Fence Installation Is Failing
Most Dallas fence failures announce themselves slowly, then all at once. Here’s what we actually see on service calls:
- Post lean at the base. The post wasn’t set deep enough for Dallas clay, or the concrete collar cracked because water pooled at the base. We’re pulling posts and resetting them below the frost line with gravel drainage so they don’t heave again.
- Gate drag and latch misalignment. The hinge side of a PGT aluminum frame will sag faster if the post was under-filled with concrete. The gate drops a quarter inch, the latch stops catching, and suddenly the fence feels ten years older than it is.
- Rails pulling free at the screw holes. Aluminum rails in Texas heat expand more than people expect, and original hardware will eventually wallow out the hole. A rail that’s loose at the factory screw point usually needs a sturdier bracket, not just a thicker screw.
- Pickets bowing or cupping. On vinyl PGT lines, direct afternoon sun across a wide run without enough expansion clearance will warp pickets. It’s not a defect; it’s physics. Properly gapped, the pickets move without buckling.
- Corrosion at the post-to-panel joint. Where dissimilar metals touch, or where fertilizer splash-back hits the base, you’ll see white bloom or pitting before the aluminum fails outright. Caught early, it’s a clean-and-treat. Left alone, it’s a re-post.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
A full PGT-compatible fence installation in Dallas runs $3,500 to $9,000 installed. The spread comes down to footage, post replacement count, gate hardware, and whether your ground is friendlier near Garland or rockier out toward Irving. At the lower end, you’re looking at a modest backyard run with existing posts in good shape. At the top, you’re clearing an old fence, resetting every post, and hanging custom hardware.
What you get from us is a written price before we pull a single post. That number covers removing old material, setting new posts in concrete with proper drainage, hanging the panels and gate, and hauling debris off your property. We don’t hand you a verbal range and then discover problems at the door. Every project carries our 365-Day Done Right Promise in writing: if something we installed fails in the first year, we come back and make it right at no charge. If it fails again, the second trip is free, too.
DIY or Call Us?
Fence work doesn’t carry the same danger as a garage spring or an electrical panel, but it’s not risk-free, especially when you’re pulling a buried post next to a gas line or a Comcast drop the previous owner buried four inches down. In most Dallas suburbs, the utility locate is free, and skipping it is how a Saturday project becomes a Tuesday repair bill.
What you can reasonably check yourself: whether posts are loose at the base, whether the gate still closes cleanly, whether rails have pulled from their brackets. What we’d tell you to leave alone is anything involving concrete extraction, post-hole digging near known utility easements, or re-tensioning a gate frame. Those jobs go faster with the right auger and the right insurance. If you’d rather hand it off, call Trevor and the crew at (940) 204-5368. We’ll give you a number, in writing, before we pick up a shovel. That’s the only way we know how to start.
FAQs
In the Dallas climate, a well-set PGT aluminum fence typically lasts 20 to 25 years, while vinyl lines hold up 15 to 20 years before UV damage and post movement start to show. The difference is usually the posts, not the panels. If you’re noticing issues at year eight or ten, it’s almost always an installation problem, not a PGT material failure. Call (940) 204-5368 for an exact assessment, and the estimate is free.
Yes, most PGT fence damage is repairable at the section or post level, and in Dallas we commonly replace individual rails, pickets, and gate hardware without touching the rest of the run. The exception is when multiple posts are compromised or the panel profile has been discontinued and can’t be matched cleanly. We’ll tell you if repair makes sense or if replacement costs less per year of remaining life, and that recommendation comes with a written quote either way.
For a typical Dallas backyard, a full PGT-compatible fence installation takes two to three working days from post holes to final hardware, with a day of that being concrete cure time before we hang panels. A section repair or gate swap is usually done in half a day.
We carry the common PGT-compatible aluminum and vinyl rail, bracket, and hinge profiles on the truck, but specific discontinued colors or custom picket widths may need to be ordered. We’ll confirm availability before scheduling so you’re not left with a gap in the fence line. Call (940) 204-5368 with your measurements and we’ll check stock while you’re on the phone.
Written by Trevor Nash, Owner, Penhallow Remodeling Dallas at Penhallow Remodeling Dallas, serving Dallas and nearby areas.
